Vessel Ionizer-Fan Type F6CL-E (with clip)

No.F6CL-E Ionizing Mini-Fan with Clip

●Ionizing method: Piezoelectric high-frequency AC corona discharge.

●Featuring a compact, lightweight design. Compact fan-shaped ionizer.

●Interior LED light lets you check for dirt on the electrode needles visually.

●By detaching the louver, the needles can be easily cleaned. Automatic shutoff for electrode over the needles.

●Comes with a clip for easy installation. The unit can be flexibly installed on a cell-production stands or desks at most appropriate angles.

●Warning indicator notifies you if the fan locks up or abnormally high voltage is detected. LED lamp notifies you in case of abnormalities. Also, its safety mechanism automatically stops the fan and ion generation when the louver is taken off.

 Specifications

Ion Generation Method	High Voltage AC Corona Discharge
Output Voltage	AC 3.5kV
Input Voltage	DC 24V  ±5% 253mA (typ.)
Dimensions	NO CLIP: 5.1"x3.1"x3.2" (131x77x81mm) H x W x D
Weight (with CLIP)	1.1 lbs (514g)
Fan Speed	HI: 0.87m3/min (max) / LOW: 0.4m3/min
Noise Emission	HI: 58.5dB / LOW: 40.4dB
Ozone Generation	0.05ppm or less (measured at 1.97" / 50mm in front of unit)
Working Temp. Range / Working Humidity Range	41~104°C / 35~65% RH (no condensation, no freezing)  5~40°C / 35~65% RH (no condensation, no freezing)
Distance from Target	5.9"~23.6" (150~600mm)
Static Eliminating Time	See PERFORMANCE
Ion Balance	Within ± 10V (measured at 11.8"/300mm from device)
Replacement Parts	See ACCESSORIES

W	H	D	Weight	EDP No.
			（clip included）
mm	mm	mm	g
77	131	81	514	621632

※The above measurement does not include the clip and other protruding parts.

・Power supply：DC24V±5%
・Current consumption：253mA (typ.)
・Noise level：58.5dB〔Fan speed: HI〕　40.4dB〔Fan speed: LOW〕
・Fan speed：0.87m³/min〔Fan speed: HI〕　0.4m³/min〔Fan speed: LOW〕
・Accessories：Power supply transformer　№AD24-ITF6　　AC cable（1.8m）

Power Supply

●Static erasing performance



Charged plate monitor:TREK 158, which conforms to ANSI EOS/ESD S3.1, was used for measurement.
Measurement conditions: Max. fan speed, Temperature: 25℃, Humidity: 50%

Top: Ion balance
Middle: Decay time required for static discharge from +1000V to +100V
Bottom: Decay time required for static discharge from –1000V to –100V

※Static electricity erasing capability values given in this catalog were obtained in our
measurement environment. Your results may differ depending on the operating environment.

========================================================
notes:
1. From Vessel website :
No.F6CL-E /F6ST-E Ionizing Mini-Fan（10/12/10）

Developmental background

The first of its kind worldwide, VESSEL first developed the fan-type static electricity elimination equipment SDJ-08 in 2003, featuring easy installation with a "clip." Especially in cell production systems, this equipment has become an essential part of the production process. The clip installation method allows for the static electricity removal device to be attached to a pipe on cell production benches, providing an ion blow on the worktable underneath the device. The special characteristics of the equipment are its space-saving aspect and reliable static electricity removal.The successor to the original model, the F-6 series is composed of mini-fan static electricity elimination equipment featuring a compact design with a miniature piezoelectric transformer and interior LED lights installed to visually check for dirt on the electrode needles and the general operation situation. The F-6Cl model can be easily installed on a pipe on a cell production bench, and freely pointed in any orientation or angle desired due to its clip type attachment method. In addition, the F-6ST model, which comes with a low-cost table stand, is on sale at the same time. This equipment provides superior static electricity elimination performance through the use of a piezoelectric transformer that provides for long-range ionization and a powerful high-speed fan.

Description

・Compact and light mini-fan type static electricity elimination equipment.

・Equipped with a clip, the F-6CL model can be easily attached to a pipe on a cell production chassis or the side of a desk or table.

・The F-6ST model is equipped with a desktop type stand for use on a worktable.

・Equipped with screw holes on three sides of the device, the stand or clip can be removed for compact installation on equipment or jigs.

・During operation, the interior light (bright white LED) shines brightly and lets you easily check for dirt on the electrode needles or check the general operation situation.

・Maintenance and removal of the electrode needle unit can be easily conducted without any special tools.

Features

・Highly reliable piezoelectric AC method employed, providing superior ion balance (within ±10V).

・Compact and space-saving, ideal for installation on cell production benches.

・Equipped with screw holes on three sides, for compact installation on equipment or jigs (M5x0.8 screws at 3 locations).

・Fan speed can be switched to either a HIGH or a LOW setting.

・Equipped with a compact and powerful "high-speed fan," performance loss is minimized even if the filter gets dirty.

・The interior light (bright white LED) shines brightly during operation allowing you to easily check for dirt on the electrode needles or check the general operation situation.

・Equipped with a warning lamp, which notifies you if the fan locks up or abnormally high voltage is detected.

・Low voltage 24V DC power supply minimizes electrical leakage and interference with nearby devices.

・The louver (electrode needle unit) can be attached or detached and the needles can be easily removed.

・The highly efficient ionizing design method minimizes ozone production.

Main usage

ESD measures for electronic components in trays on a cell production bench, prevention of static electricity for resin parts, and the prevention of detachment in the presence of a static electric field, etc.The prevention of static electricity during work on conveyor lines in production facilities and the prevention of detachment in the presence of a static electric field, etc.Semiconductor production plants, the manufacturing of electronic equipment, the manufacturing of precision machinery, production in the food industry, the production of packing materials, printing, painting, and the production of pharmaceuticals, etc.

 

Accessories:

Electrode Needle Unit  Power Supply
================= notes: 1. actual photos:  2. you can clip the Vessel F-6CL ionizer anywhere conveniently just like this similar to Vessel SDJ-08